Section contents:
Primary Siemon Company Logo
All logos and guidelines for their usage must be followed as below.
- Do not change, redraw or alter the logo in any way
- Logo may be scaled to meet output requirements as needed within size guidelines below
- Logo proportions must not be altered
- Logo typeface is an imbedded element of the defined logo and must not be altered
There are four versions of the primary Siemon logo available:
Full color logo on white background. To be used in most circumstances.
B
Black color logo on white background. Only used when color isn’t available or using a very small size logo.
C
White logo on black background. Only use when color isn’t available or using a very small size logo.
D
Full color logo on black background. To be used in most circumstances.
Please Note: If you require a Siemon logo for embossing, engraving, or molding, please contact the Siemon Corporate Marketing team.
Incorrect Usage: The following are examples of how not to use the Siemon logo.
DO NOT
Overlap the logo
Tilt the logo
Change any colors
Use the white logo on a white background
Use the black logo on a dark background
Use the logo on a multicolored background
Apply an outline or stroke
Skew or distort the logo
Outline or stroke the white logo
Put a box around the logo
Spacing and Sizing
To ensure the Siemon logo is always prominent, there is a minimum exclusion zone area surrounding it.
- No other graphic or text element may appear within its zone.
- The zone must be used in all applications of the mark.
- The minimum required area surrounding each version of the Siemon mark is in proportion to the overall dimensions of the mark. This relationship stays the same, whatever the marks reproduction size.
- The illustration shows how to establish the zone, the logo size is expressed as a ratio to the exclusion required around it.
To present the Siemon brand properly, it is essential that the mark be reproduced with consistent quality. No version of the Siemon mark may be reproduced below the minimum size specified below. This illustration shows the dimensions for minimum size.
The Siemon brand mark will be applied using a wide range of printing and reproduction techniques, to an equally wide range of base materials. It is therefore important that you consider carefully the technique and base materials before choosing the appropriate mark type. For example, if producing a color logo, you should use a technique that will guarantee the accurate registration of the colors. Similarly, if you are using a single-color logo, the reproduction method and base material should ensure the mark appears crisp and clearly.
Embossed or Etched Versions
In order for the Siemon logo to appear on items where size and reproduction methods will reduce its clarity the standard single-color logo should be used.
It should be used in black (example E below) or etched onto metal (usually reverse as in example F below). All guidelines on color and background must be followed. The logo may be used in either the positive or negative form.
Minimum acceptable dimensions for reproducing the Siemon logo in this format are: 1.25in W x 0.5in H (32mm W x 13mm H).
Examples of reproduction where use of the small promotion mark may include: embroidery, embossing, engraving. E.g. partner web site/promo material where limited space available, small promo items such as golf tees, pens etc.
E
F
Secondary Logo
Stacked Logo
The Stacked Logo is subordinate to the Primary Logo. Only use this version of the logo where the Primary Logo cannot be used due to space constraints, such as in square print areas or certain social media thumbnails/icons .
Spacing for this logo is equal to 1/3 of the height and width of the logo.
Tertiary Logo
The tertiary icon logo may only be used on materials in/on which the primary Siemon logo also appears. It must not be used as a standalone logo.
It is intended exclusively for use in small areas in which the primary or tertiary logos cannot be used due to size or resolution constraints.
The Siemon icon should appear no smaller than one-quarter of an inch wide or 24 pixels. Spacing for this icon is equal to 1/3 of the height and width of the logo.
Primary Logo
Secondary Logo
Tertiary Logo
Logo Colors
The colors shown below are those used to represent Siemon and its brand identity – Pantone 185, Black and White. Due to the fact that they will be applied to a wide range of materials and finishes it is not possible to list specific color references for all applications, however we have listed the references for use in print and electronic documentation, which are the most common formats used.
Pantone 185
R: 239 G: 62 B: 66
C: 0 M: 91 Y: 76 K: 0
Hex: #EE3A43
Black
R: 0 G: 0 B: 0
C: 100 M: 100 Y: 100 K: 100
Hex: #000000
White
R: 255 G: 255 B: 255
C: 0 M: 0 Y: 0 K: 0
Hex: #FFFFFF
Print/Electronic References
When on a standard web or sheet fed press, accurate color reproduction can be achieved by
accurately matching to solid PANTONE colors (PMS 185), the standards for which are shown in the PANTONE color formula guide 1000.
Important: When printing onto uncoated paper (this applies to letterhead and business cards) the print vendor must be aware to run job at a density reading of 1.19 through the magenta filter on a densitometer for a richer looking Pantone 185. Otherwise global inconsistency of color of logo will occur.
When printing process color, the color breakdown is as follows:
C = 0, M = 91, Y = 76, K = 0
For electronic communication, the Red, Green, Blue (RGB) breakdown is as follows:
R = 239, G = 62, B = 66
Please note: The colors printed on this page are not intended to match to the PANTONE, CMYK or RGB color standards. They are for use as a guide only and must not be used for color matching during the proofing process.
Website/Electronic Usage
Any use of the Siemon logo on a third parties’ website should incorporate a hyperlink back to the appropriate Siemon site. The URL www.siemon.com should be used as the default option. In order for the logo to appear prominent on a web page, we recommend a minimum exclusion zone of 5 pixels (at 72 dpi) around the logo.
If the logo is used in animation, video, PowerPoint presentations, or other rich media, the logo should not be animated, distorted or embellished in any way.
Co-Branding Guidelines
Frequently we work with various partners on joint marketing campaigns. The information below provides clear guidance on how to execute co-branding activities for Siemon with other partner brand assets.
Logo Treatment
In order to ensure that each logo has visual impact and conveys the appropriate relationship we need to define clear space and margins between them.
Depending on the background chosen, the selection of full color/single color logos needs to be considered to ensure that all the logos are correctly visible. Regarding separation distances, please ensure you adhere to the Siemon logo spacing and sizing parameters and ensure that all partner logos are equally spaced.
Logo Positioning
Each logo should be vertically/middle – aligned for the best balance. The left position of the logo indicates brand dominance in brand-neutral environments. This positioning will typically be driven by the instigator of the activity and/or with the logo of the best-known brand in the market.
Partner Visuals
In select instances, a partner might want an expanded CTA to include visuals. Though it’s not common practice, this is how we would do that while still maintaining our brand’s look and feel.
- Brand creative should always take up at least two thirds of the overall visual space
- Partner messaging — including visuals, CTA and contact information — can occupy up to one third of the real estate
- Partner visuals, such as headshots, should take up no more than one quarter of the allocated partner space
Other Logos
Usage guidelines for the following must be followed as below.
- Do not change, redraw or alter the logo in any way
- Logo proportions must not be altered
- Logo typeface is an imbedded element of the defined logo and must not be altered
